blade height
英 [bleɪd haɪt]
美 [bleɪd haɪt]
网络 叶片高度
双语例句
- The uniform distribution of aerodynamic load along the blade height due to the nearly radial distribution of passage shock makes the stage with positively curved rotor have the highest efficiency.
正弯曲动叶中通道激波在顶部前移，失速裕度下降，通道激波近似为径向，负荷沿叶高分布均匀，气动效率最高。 - The paper stresses the necessity of considering reaction variation along with blade height.
强调计算推力必须计及反动度沿叶高的变化。 - The cutting current, cutting speed of the sawing experiments, damage morphology of diamond particles in the blade after cutting abrasive and protrusion height are compared.
对比锯切实验中的切割电流、切割速度等参数。检测经过切削后的刀头中的金刚石颗粒的磨粒破坏形态及出刃高度。 - The effects of suction surface fences at different blade height on the cascade loss and secondary flow in compressor cascade were investigated through the detailed cascade exit flow field survey in low speed wind tunnel.
在低速风洞上通过详细测量叶栅的出口流场，研究了叶片吸力面上不同高度处加翼刀对压气机叶栅损失和二次流的影响。 - Load distribution of axial fan along to the blade and blade height is put forward according to dynamic design method of quintic equation.
提出了轴流通风机沿叶片叶高的载荷分布，按五次方流型设计的方法。 - The results indicated that there were significantly positive correlations between seed yield per plant and number of ears per plant, number of grains per ear, ear length, blade weight, plant height, 1 000 grain weight and stem weight.
结果表明，7个农艺性状与单株种子产量均呈显著的正相关，其相关系数的大小依次为：单株穗数＞每穗粒数＞穗长＞叶片重＞株高＞千粒重＞茎重。 - By using a numerical calculation method compared and studied is the influence of different circumferential curving of guide vanes on cascade flow performance. The study involves the distribution of total pressure loss factor, outlet gas flow static pressure and Mach number along the blade height.
应用数值计算的方法，比较研究了某型导叶叶片不同周向弯曲对叶栅流动性能的影响，结果包括总压损失系数、出口气流静压、马赫数沿叶高分布。 - The change of imported Mach number has great influence on the20%-60% blade high impact on the diameter of stator. Especially, the flow structure and parameters has been tremendously affected under the influence of flow Mach number in the40% blade height.
进口马赫数变化对静叶中径附近20%-60%叶高影响较大，尤其是在40%叶高处流场结构和参数受来流马赫数的影响最大。 - Meanwhile, the flow angles and static pressure ratios of different blade height are increased, so the performance of optimized blade is much better than the original blade.
同时因为在不同叶高处，优化叶片的气流转折角增大，静压比升高，从而使优化叶片性能高于原始叶片。 - The forming blade is a kind of blade in which the circular radius of the back are profile in each blade section does not vary with the height, that is, it can be machined with a form milling cutter.
成型面叶片是指叶片型面沿叶高各截面内背弧型线的圆弧半径不随叶高变化、均相同的叶片，即可用成型铣刀加工出来的叶片。